Old 03-26-2023, 08:11 AM
LudwigGuy LudwigGuy is offline
Join Date: Apr 2022
Posts: 39
Default Repairing peeling wrap
This question has been answered a million times, so feel free to post links to answers instead of typing up your answers if you like!

I just ordered an early 70s 3-ply kit, but the wrap has a slight peel to it. I need to know what kind of glue to use if (A.) the wrap will be overlapped on itself and (B.) if the wrap has shrunk and will actually be glued to the wood shell.

Thanks in advance!
Old 03-26-2023, 07:31 PM
MarkD MarkD is offline
Advanced Member
Join Date: Sep 2005
Location: Sheboygan Wisconsin
Posts: 161
Default Re: Repairing peeling wrap
I would say the best way in any instance is to duplicate what the factories used, and that was likely a very fast setting highly nasty industrial grade contact cement. Slap that wrap on lickety split, rolly polly with a tool, trim excess at bearing edges-etc if need be, down the line it went. Drill holes, mount hardware, bada beep..They sure weren't using Elmer's Glue. Stuff would probably kill you, from Cancer. LOL

Yep, you have to be neat, like a surgeon with Contact Cement, take whatever precautions you like, masking around the area, having some small brushes to apply, and then keep the two parts apart for a good number of minutes. A hair dryer on low may even help speed drying.

And the really delicate part, is to get that glue under the wrap, by very gently lifting the wrap, without cracking-breaking the wrap, you dig?
Then press all back together firmly, even hold for a short while.

Dry time could take 20-30 minutes.

You should be good for the next 25 years.
If you were sloppy and have excess, something like Goof Off-etc will likely remove any tell tale signs of visible tell tale glue residues.

Companies like 3M make the really good stuff, snort that stuff for 6-8 hours straight like I have many times, you will be spaced, but something like the DAP Contact Cement from Home Depot will work just fine as well.

Just have an understanding-education about how contact cements are to be used.

Last edited by MarkD; 03-26-2023 at 07:44 PM.
Old 03-27-2023, 07:45 AM
LudwigGuy LudwigGuy is offline
Join Date: Apr 2022
Posts: 39
Default Re: Repairing peeling wrap
This is perfect. Thank you for taking the time to write all of this up! I have some contact cement headed my way this morning, and hoping I'll be getting to work this afternoon.

Thanks again!
Old 03-31-2023, 03:46 PM
OddBall OddBall is offline
Vintage Drum Guru
Join Date: Oct 2010
Location: Boston MA.
Posts: 6,522
Default Re: Repairing peeling wrap
There's really nothing else to add Mark covered it well. But, I used a roller skate to roll the seam.
It`s a drum,.....Hit It !!

.....76/#XK9207 Phonic Sound Machine D454/D-505 snares !i
Old 04-04-2023, 01:16 PM
MarkD MarkD is offline
Advanced Member
Join Date: Sep 2005
Location: Sheboygan Wisconsin
Posts: 161
Default Re: Repairing peeling wrap
Again, I can't stress enough allowing the proper dry time with Contact Cements, It's better to err on longer dry times given any such product.

Properly dried before bonding, such cements-glues will be dry to the touch. Small makeshift small wedges or such to help keep/lift the wrap away from the shell while the cement dries will be wise.

Again, the product must be applied to "Both" pieces to be re-glued.

Be careful with wraps in how far you may lift them to apply cements, you don't wish to damage-crack the wrap. Don't go any further than necessary.
Old 04-07-2023, 01:36 PM
microswitch microswitch is offline
Contributing Member
Join Date: Mar 2016
Location: Los Angeles
Posts: 144
Default Re: Repairing peeling wrap
Some swear by the double-side tape method, and that is ok I have used it too BUT ( notice the big but). that is good for small size like 12 or 13 toms. For a BD nothing beats contact cement. I normally center the wrap on the shell with small clip; after I'm satisfied with the alignment I place a 2x1 piece of wood, edge side across the shell and clamp it, holding securely the wrap in place.
Then I start the process of the contact cement. One side first then the other side. It may seem a bit cumbersome at first but it the method that gives me the best results. My wrap is always centered and secure.
As far as using the tape I only use " FAST TAPE" strong but very forgiving.
Old 06-25-2023, 04:41 AM
Rik_Everglade Rik_Everglade is offline
Vintage Drum Guru
Join Date: Jun 2012
Posts: 522
Default Re: Repairing peeling wrap
Both of these techniques have worked for me when there is a full width overlap...like 3/4 inch or more. Some wraps are quite resistant to that type of repair. Sometimes the wrap curls up. When the overlap has integrity but for the 3/8 inch curl, I clamped a long straight edge, happened to be a sturdy long level, used a fresh blade in a utility knife and carefully cut it off, and maybe relic it just a bit.

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Collapse Forum Rules Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Search Options
Tag Search Advanced Search