Search
Register
Only Admins can see this message.
Data Transition still in progress. Some functionality may be limited until the process is complete.
Processing Attachment, Gallery - 134.47182%

Telescoping Stands-Parts Stuck Together-How to get "Un-Stuck"?

Posts: 1685 Threads: 529

Greetings,

I just got a Ludwig Flat Base Cymbal Stand on Reverb.com (a good alternative to sleazebay by the way-run by musicians for musicians) and the base and middle sections are stuck together, with the wing screw the holds the middle section in place completely removed.

What is the best way to get them "un-stuck"? I tried tapping on both sections with a rubber mallet and no dice.

I obviously want to keep everything in tact and as least damaged as possible. If the lower section's top insert is fried (which it most likely will be), I have other "Ludwig base section top tightener" parts I can use (For lack of a better term), so it will not be a show stopper.

Any suggestions?

Thanks!

V

Posted on 9 years ago
#1
Posts: 219 Threads: 36

Here's an odd thought based on a recent vintage pocket watch that I couldn't get apart. I got the crystal off and removed the movement, but the metal back wouldn't budge; it was threaded and screwed on/off. I first tried heat, thinking on the lines of expansion /contraction. It might've helped some, but I still couldn't get it, sooooo I put it in the freezer for a few minutes - ka-ching! screwed right off. Your milage may vary, but it could be worth a try. Good Luck

...but when he played on his drum, he made the stars explode....
Posted on 9 years ago
#2
Posts: 1460 Threads: 87

If you have any of inside piece exposed, you could might try a strap wrench on both pieces to twist them apart.

Could try driving out the inside pipe using a washer ground to the inside diameter of the of the outer pipe.

Posted on 9 years ago
#3
Posts: 1537 Threads: 117

PB Blaster auto parts stores. Let it soak a day or two. Tap with mallet. Should break loose.

Creighton

Nothing special here but I like them.
Posted on 9 years ago
#4
Posts: 5295 Threads: 226

I agree with Creighton...Lubrication and patience is the solution here...

Cheers

1976 Ludwig Mach 4 Thermogloss 26-18-14-14sn
1978 Ludwig Stainless 22-22-18-16-14-13-12 c/w 6-8-10-12-13-14-15-16-18-20-22-24 concert toms
1975 Sonor Phonic Centennials Metallic Pewter 22-16-13-12-14sn (D506)
1971 Ludwig Classic Bowling Ball OBP 22-16-14-13
1960's Stewart Peacock Pearl 20-16-12-14sn
1980`s Ludwig Coliseum Piano Black 8x14 snare
1973 Rogers Superten 5x14 & 6.5x14 COS snares
1970`s John Grey Capri Aquamarine Sparkle 5x14 snare
1941 Ludwig & Ludwig Super 8x14 snare
Posted on 9 years ago
#5
Posts: 9005 Threads: 266

From Creighton

PB Blaster auto parts stores. Let it soak a day or two. Tap with mallet. Should break loose.Creighton

I agree... I had a 100+ year old stand that was rusted together and the PB Blaster got them loose in 30 minutes.

John

Too many great drums to list here!

http://www.walbergandauge.com/VintageVenue.htm
Posted on 9 years ago
#6
Posts: 341 Threads: 53

PB blaster gets my vote too. Or wd40 if u can't find PB

Surrounded by drummers here! (I am a guitarist.)
-------------------------------------

1970/71? Ludwig Downbeat in Blue Oyster Pearl
http://www.vintagedrumforum.com/showthread.php?t=33677
Posted on 9 years ago
#7
Posts: 721 Threads: 30

Put them in the freezer overnight. Try and try hard to pull them apart in the morning.

Remember, freezing reduces swelling.

Kind of like when you were a kid playing outside in the snow all day. The boys were reduced.;)

Joe


“I did not trip and fall. I attacked the floor and I believe I am winning.”
Posted on 9 years ago
#8
Posts: 1685 Threads: 529

Thanks for the great advice, everyone.

I had some Tri-Flow lubricant and that did the trick.

Posted on 9 years ago
#9
  • Share
  • Report
Action Another action
Something else here